Step1: Hardware Installation
Follow the official IBM video tutorial to rack and stack IBM V3700.
Cabling V3700, ESX Host and Fabric.
- Connect each canister of V3700 Storage to two Fabric. Canister1 FC Port 1—>Fabric1 and Canister 1 FC Port 2—>Fabric2. Canister2 FC Port 1—>Fabric1 and Canister 2 FC Port 2—>Fabric2.
- Connect two HBAs of each Host to two Fabric.
- Connect Disk Enclosure to two canister
- Connect Both Power cable of each devices to multiple power supply
Step2: Initial Setup
Management IP Connection: Once you racked the storage, connect Canister1 Port 1 and Canister 2 Port 1 into two Gigabit Ethernet port in same VLAN. Make LACP is configured in both port in your switch.
Follow the official IBM video tutorial to setup management IP or download Redbook Implementation Guide and follow section 2.4.1
One initial setup is complete. Log on to V3700 storage using Management IP.
Click Monitoring>System>Enclosure>Canister. Record serial number, part number and machine signature.
Step3: Configure Event Notification
Click Settings>Event Notification>Edit. Add correct email address. You must add management IP address of v3700 into Exchange Relay Connector. Now Click test button to check you received email.
Step4: Licensing Features
Click Settings>General>Licensing>Actions>Automatic>Add>Type Activation Key>Activate. repeat the step for all licensed features.
IBM V3700 At a Glance
MDisk: Bounce of disk configured in preset RAID or User defined RAID. For example you have 4 SSD hard drive and 20 SAS hard drive. You can chose automatic configuration of storage which will be configured by Wizard. However you can chose to have 1 RAID5 single parity MDisk for SSD and 2x RAID5 MDisk with parity for 20 SAS hard drive. In this case you will have three MDisk in your controller. Simply MDisk is RAID Group.
Pool: Storage Pool act as container for MDisks and available capacity ready to be provisioned.
Volume: Volumes are logical segregation of Pools. Volume can defines as LUNs and ready to be mapped or connected to ESX host or Hyper-v Host.
Step5: Configure Storage
Click Pools>Internal Storage>Configure Storage>Select recommended or user defined. Follow the wizard to complete MDisk.
Step6: Configure Pool
Click Pools>Click Volumes by Pool>Click New Volume>Generic>Select Quantity, Size, Pool then Click Create.
Repeat the steps to create multiple volumes for Hyper-v Host or ESXI host.
Important! In IBM V3700, if you configure storage using GUI, GUI console automatically select default functionality of the storage for example number of mdisk. you will not have option to select disks and mdisk you want. Example, you may want create large mdisk containing 15 disks but GUI will create 3xmdisk which means you will loose lot of capacity by doing so. To avoid this, you can create mdisk, raid and pool using command line.
Telnet to your storage using putty. type username: superuser and password is your password. Type the following command.
Creating RAID5 arrays and a pool
svctask mkmdiskgrp -ext 1024 -guiid 0 -name Pool01 -warning 80%
Creating a spare with drive 6
svctask chdrive -use spare 6
Creating a RAID Group (12 disk)
svctask mkarray -drive 4:11:5:9:3:7:8:10:12:13:14 -level raid5 -sparegoal 1 0
Creating SSD Raid5 with easy tier (disk0, disk1, disk2 are SSD)
svctask mkarray -drive 1:2:0 -level raid5 -sparegoal 0 Pool01
Now go back to GUI and check you have created two mdisk and a Pool with easy tier activated.
Step7: Configure Fabric
Once you rack and stack Brocade 300B switches. Connect both Brocade switches using CAT6 cable to your Ethernet Switch. This could be your core switch or an access switch. Connect your laptop to network as well.
username: root password: fibranne
username: admin password: password
Connect the console cable provided within brocade box to your laptop. Insert EZSetup cd into cdrom of your laptop. Run Easy Setup Wizard.
Alternatively, you can connect the switch to the network and connect to it via http://10.77.77.77 (Give yourself an IP address of 10.77.77.1/24). Use the username root and the password fibranne
If you don’t want to do that, connect the console cable (provided) to your PC and launch the EZ Setup Software supplied with the switch. Select English > OK.
At the Welcome Screen > Click Next > Click Next > accept the EULA > Install > Done > Select Serial Cable > Click Next > Click Next (make sure HyperTerminal is NOT on or it will fail). It should find the switch > Set its IP details.
Next > Follow Instructions.
Install Java on your laptop. Open browser, Type IP address of Brocade, you can connect to the switch via its web console Once logged in using default username:root and password: fibranne
Click Switch Admin>Type DNS Server, Domain Name, Apply. Click License>Add new License, Apply.
Click Zone Admin>Click Alias>New Alias>Type the name of Alias. Click Ok. Expand Switch Port, Select WWNN>Add members. Repeat for Canister Node 1, Canister Node 2, ESX Host1, ESX Host2, ESX Host 3….
Select Zone Tab> New Zone > Type the Name of Zone, Example vSphere or Hyper_v. Select Aliases>Click Add Members> Add all Aliases.
Select Zone Config Tab>New Zone Config>Type the name of Zone Config>Select vSphere or Hyper_V Zone>Add Members
Click Save Config. Click Enable Config.
Repeat above steps for all fabric.
Step8: Configure Hosts in V3700
Click Hosts>New Host>Fibre Channel Host>Generic>Type the Name of the Host>Select Port>Create Host.
Right Click on each host>Map Volumes.
Step9: Configure ESXi Host
Right Click on ESX Cluster>Rescan for datastores>
Click ESX Host>Configuration>Storage>Add Storage>Click Next>Select Correct and Matching UID>Type the matching Name same as volume name within IBM V3700. Click Next>Select VMFS5>Finish.
Rescan for datatores for all Host again. you will see same data store popped up in all Hosts.
Finding HBA, WWNN
Select ESX Host>Configuration>Storage Adapters
Right Click on Storage>property>Manage Paths
Finding and Matching UID
Log on to IBM V3700 Storage>Volume>Volumes
Click ESX Host>Configuration>Storage>Devices